Complete gasket kit for our BAR-TEK® pop-off valve.

A leaking pop-off valve can cause loss of power and engine lean. Engine lean will lead to engine damage.

Therefore, we recommend to service the pop-off valve regularly to prevent damage. 

Scope of delivery:

• 3x sealing ring large
• 1x sealing ring small

Manufacturer

Information about the manufacturer

BAR-TEK®

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

A must have BILLET cover for all EFR Turbos running high boost!

The OEM Bov cover can fail due to high boost.
The reason is the week material.

Our special Race cover is made from high performance material.

Manufacturer

Information about the manufacturer

BAR-TEK®

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Service kit for Forge Motorsport blow off valves. For all open and closed blow off valves from Forge.

Wear also occurs in a blow off valve, which is why it should also be serviced and checked regularly. Depending on the model of the blow off valve, the service kit includes sealing rings, piston, springs and the special grease.

If the Forge blow off valve is cared for and maintained, it will last a lifetime.

Please select the model.

Attention: Scope of delivery may vary depending on the service kit.

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Now you can fine tune your double-piston Blow Off/Diverter Valve to the exact needs of your engine with this complete tuning kit.

Your valve tuning kit you will find four springs.

The strongest spring is the red, followed by the blue, yellow and finally the green which is the weakest. The spacers enable you to fine tune the settings between two spring tensions if required.

Please note - fitting a stronger spring into a valve will not increase boost pressure unless existing pressure is being lost. Failure to allow the valve to operate by installing a spring which is to strong may cause damage to the turbocharger.

The red coded springs should not be installed in the DVR or DV007 diaphragm valves

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Now you can fine tune your Blow Off/Diverter Valve to the exact needs of your engine with this complete tuning kit.

Your valve tuning kit you will find four springs.

The strongest spring is the red, followed by the blue, yellow and finally the green which is the weakest. The spacers enable you to fine tune the settings between two spring tensions if required.

Please note - fitting a stronger spring into a valve will not increase boost pressure unless existing pressure is being lost. Failure to allow the valve to operate by installing a spring which is to strong may cause damage to the turbocharger.

The red coded springs should not be installed in the DVR or DV007 diaphragm valves

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Citroen Xantia Turbo Dump Valve Fitting Kit from Forge.

Kit for fitting a dump / blow off valve to a Citroen Xantia.

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

\"Blow Off Valve from FORGE for Peugeot 307 GT Turbo.

-keeping external noise to the minimum
-quicker throttle response
-higher clamping load to maintain boost pressure\"

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Blow off valve from FORGE for Fiat Uno Turbo, Fiat Punto, Opel Calibra and Cavalier, Citroen Xantia, Toyota MR2 and Ford Escort RS Turbo.

The FMDV004 is made of billet aluminium.
The charge air is released by the pop-off valve, creating the \"whoosh\" effect.
This speeds up the throttle response and increases the clamping force. This increases the reliability of the boost pressure.

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Blow Off Valve from FORGE for Hyundai Genesis Turbo, Veloster Turbo and Sonata Turbo.

The FMDVHGA Blow Off Valve is made of billet aluminium.

-keeping external noise to the minimum
-quicker throttle response
-higher clamping load to maintain boost pressure

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

\"This Turbo Recirculation Valve from FORGE is one of the best Pop Off valves.

The FMDV008 can be adapted to boost preasures of different applications.

The new design enables a greater flow than the OEM valve.

The compact design saves space under the engine cover.\"

In The Box:
1x FMDV008 Valve
1x Uprated Yellow Spring
1x Uprated Blue Spring
1x Cable Tie
1x 2.5mm Allen key
2x 35mm Hose Clamps
1x Instruction Booklet
1x Forge Sticker

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Blow off Valve RS Atmospheric from Forge.

This valve has been specially developed to allow a higher flow rate. A 50mm (2 inch) bore provides improved turbo acceptance.

25mm or 34mm connector.

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Closed sport piston dump valve from Forge especially for larger turbochargers!

High-quality Forge aluminium piston pop-off with genuine aluminium piston (closed system). Ideal for all performance-enhanced turbocharged vehicles with large turbocharger.

Easy to replace with the original Bosch pop off.

25mm or 34mm connector.

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

External turbo drain valve from FORGE with two springs.

The FMWG001 drain valve utilises a piston mechanism and is designed to withstand high hp capacities and temperatures.
Allows fine adjustment.

Please select the springs.

1.1bar/15.9PSI=large green + small yellow
1.2bar/17.4PSI=large yellow + small yellow
1.3bar/18.8PSI=large blue + small yellow
1.4bar/20.3PSI=large red + small yellow
1.5bar/21.7PSI=large red + small blue
1.6bar/23.2PSI=large red + small red

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

\"Twin Blow Off Valve Kit from FORGE for Nissan Skyline R32.

-keeping external noise to the minimum
-quicker throttle response
-higher clamping load to maintain boost pressure\"

Manufacturer

Information about the manufacturer

Forge Motorsport

Forge Motorsport

Unit 1A, Ashville Trading Estate, Gloucester, GL2 5EU. Larchtower, United Kingdom

https://www.forgemotorsport.co.uk/Contact.html

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Original Garrett BOV outlet adapter

• for GVB-50R
• Perfect fit 
• Aluminium

Manufacturer

Information about the manufacturer

Garrett

Garrett Motion Inc.

Z.A. La Pièce 16, Rolle, VD, 1180 Switzerland

https://www.garrettmotion.com/contact/

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Original Garrett BOV outlet adapter

• for GVB-50R
• Perfect fit 
• Aluminium

Manufacturer

Information about the manufacturer

Garrett

Garrett Motion Inc.

Z.A. La Pièce 16, Rolle, VD, 1180 Switzerland

https://www.garrettmotion.com/contact/

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Original Garrett BOV outlet adapter

• for GVB-50R
• Perfect fit 
• Aluminium

Manufacturer

Information about the manufacturer

Garrett

Garrett Motion Inc.

Z.A. La Pièce 16, Rolle, VD, 1180 Switzerland

https://www.garrettmotion.com/contact/

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Original Garrett BOV outlet adapter

• for GVB-50R
• Perfect fit 
• Aluminium

Manufacturer

Information about the manufacturer

Garrett

Garrett Motion Inc.

Z.A. La Pièce 16, Rolle, VD, 1180 Switzerland

https://www.garrettmotion.com/contact/

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

GARRETT VENT | BLOW-OFF Valves with high flow for high performance engines

Garrett Vent | Blow-Off Valves were developed by the same engineers who designed the G-Series turbochargers and GVW wastegates.

GVB-50 is a high flow BOV with a 50mm valve available in four eye-catching colour combinations.

You have the choice between a BOV with venting to atmosphere (VTA) and one with recirculation (RCV).

Features:

• CFD-tested for maximum flow and thermal efficiency
• Replaceable components to extend service life
• Robust construction for easy membrane replacement
• 6061 anodised aluminium BOV cover and fully machined billet housing
• Maximum flow 350 CFM | .21kg/s for GVB-50R
• Four outlet adapters for the return valve are available separately
• Base pressure 0.7 Bar | 10 PSI (blue and white spring installed)
• Configurable spring settings: 0.2 Bar | 3 PSI - 0.9 Bar | 13 PSI
• Welded aluminium alloy flange
• Garrett BOV contains five springs that allow fine tuning of the pressure setting
• Springs: 17/7 PH stainless steel
• Coated stem and bushing for reduced friction and wear resistance
• High temperature resistant elastomer diaphragm reinforced with Nomex
• Fittings and fastening elements made of stainless steel
• BOV flange dimensions as for TIAL Q or QR valves

GVB-50 Blow Off Valves include all of the following parts:

• Air connection parts (nuts, bolts, washers)
• V-band set (V-band, screw, nut)
• O-ring (inlet flange)
• Welding flange
• Springs (replacement: red, green, brown | installed: blue, white)

Manufacturer

Information about the manufacturer

Garrett

Garrett Motion Inc.

Z.A. La Pièce 16, Rolle, VD, 1180 Switzerland

https://www.garrettmotion.com/contact/

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

GARRETT VENT | BLOW-OFF Valves with high flow for high performance engines

Garrett Vent | Blow-Off Valves were developed by the same engineers who designed the G-Series turbochargers and GVW wastegates.

GVB-50 is a high flow BOV with a 50mm valve available in four eye-catching colour combinations.

You have the choice between a BOV with venting to atmosphere (VTA) and one with recirculation (RCV).

Features:

• CFD-tested for maximum flow and thermal efficiency
• Replaceable components to extend service life
• Robust construction for easy membrane replacement
• 6061 anodised aluminium BOV cover and fully machined billet housing
• Maximum flow 350 CFM | .21kg/s for GVB-50R
• Four outlet adapters for the return valve are available separately
• Base pressure 0.7 Bar | 10 PSI (blue and white spring installed)
• Configurable spring settings: 0.2 Bar | 3 PSI - 0.9 Bar | 13 PSI
• Welded aluminium alloy flange
• Garrett BOV contains five springs that allow fine tuning of the pressure setting
• Springs: 17/7 PH stainless steel
• Coated stem and bushing for reduced friction and wear resistance
• High temperature resistant elastomer diaphragm reinforced with Nomex
• Fittings and fastening elements made of stainless steel
• BOV flange dimensions as for TIAL Q or QR valves

GVB-50 Blow Off Valves include all of the following parts:

• Air connection parts (nuts, bolts, washers)
• V-band set (V-band, screw, nut)
• O-ring (inlet flange)
• Welding flange
• Springs (replacement: red, green, brown | installed: blue, white)

Manufacturer

Information about the manufacturer

Garrett

Garrett Motion Inc.

Z.A. La Pièce 16, Rolle, VD, 1180 Switzerland

https://www.garrettmotion.com/contact/

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Precision BLOW-OFF Valves with maximum flow for turbo engines

The Precision Blow-Off Valves are the latest development from Precision.

The Precision valves are high-flow blow off valve with a 50 mm valve that comes in a stylish black colour.

Features:

• CFD-tested for maximum flow and thermal efficiency
• Robust construction for easy diaphragm replacement
• made from 6061 and 7075 anodised aluminium
• machined billet housing
• Rolling diaphragm for fast response
• 3 different spacers for maximum flexibility
• BOV flange dimensions same as TIAL Q or QR valves

Manufacturer

Information about the manufacturer

Precision Turbo & Engine

Wabtec Corporation

9401 Georgia Street, Suite 2, Crown Point, IN 46307, USA

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Special flange for Tial blow off valves. Weld-on flange available as a spare part in aluminium and stainless steel.

Suitable for the following blow off valves:

• Tial 50mm
• Tial Q
• Tial QR
• Tial Alpha Q

Manufacturer

Information about the manufacturer

TiAL Sport

TiAL Sport

450 S. Shiawassee St Owosso, MI 48867, United States

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Original replacement spring from TiAL

This replacement spring is suitable for changing the opening pressure of a TiAL blow off valve. The specified pressure does not refer to a boost pressure, but to the negative pressure required to open the BOV. This means that the lower this value, the sooner the BOV opens!

Manufacturer

Information about the manufacturer

TiAL Sport

TiAL Sport

450 S. Shiawassee St Owosso, MI 48867, United States

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

TIAL BV 50 QR is suitable for turbo engines up to approx. 1800hp.

The BV 50 QR Tial blow off valve has a valve diameter of 50mm and is the largest TIAL version available here in the closed version suitable for mass air flow sensors.

Both the housing and the valve are made of aluminium. The inner diaphragm is made of temperature-resistant Nomex and is additionally reinforced.

Tial uses a very high-quality stainless steel spring and thus guarantees a constant spring rate over the entire temperature range.

Included in delivery:
BV 50 blow off original TIAL
1x TiAL air connection in 25mm
1x TiAL V-band
1x weld-in adapter for attachment to the charge air pipework.

Please select body colour.

Available in:

Silver
Black
Red
Purple
Blue

Manufacturer

Information about the manufacturer

TiAL Sport

TiAL Sport

450 S. Shiawassee St Owosso, MI 48867, United States

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

TIAL BV 50 Q is suitable for turbo engines up to approx. 1800hp.

The BV 50 Q Tial blow off valve has a valve diameter of 50mm and is the largest TIAL version available here in the open version.

Both the housing and the valve are made of aluminium.

The inner diaphragm is made of temperature-resistant Nomex and is additionally reinforced.

Tial uses a very high-quality stainless steel spring and thus guarantees a constant spring rate over the entire temperature range.

Included in the scope of delivery:

• BV 50 blow off original TIAL
• 1x TiAL air connection
• 1x TiAL V-band
• 1x weld-in adapter for attachment to the charge air pipework.

Available in:

• Silver
• Black
• Red
• Purple
• Blue

Please select the colour of the body and the material of the weld-on adapter.

Manufacturer

Information about the manufacturer

TiAL Sport

TiAL Sport

450 S. Shiawassee St Owosso, MI 48867, United States

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Weld flange (inlet) - fits Turbosmart Hyper-Gate45 (45mm) External Wastegates

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Turbosmart\'s springs are designed to work with our Plumb Back, Dual Port and Supersonic blow off valves. They offer a wide range of spring rates to suit your riding style and application. Manufactured from high quality materials, Turbosmart\'s springs are designed to maintain peak performance of your blow-off valve in the most extreme conditions. Choose from our selection of Turbosmart springs to get the perfect fit for your car and the best performance from your blow-off valve.

Spring - Fits Turbosmart Ultra-Gate38 (38mm), Comp-Gate40 (40mm), Hyper-Gate45 (45mm) external wastegates and internal Wastegate actuators (IWG-75).

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Spring - Fits Turbosmart Ultra-Gate38 (38mm), Comp-Gate40 (40mm), Hyper-Gate45 (45mm) external wastegates and internal Wastegate actuators (IWG-75).

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Billet blanking plug specially developed for the Borg-Warner EFR, KKK and Ford Focus ST 2.0 EcoBoost turbocharger. Replaces the originally installed diverter valve, which is required for the installation of an external BOV.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Full recirculating Blow Off Valve. The Plumb Back system recirculates all excess pressure back into the intake system. 

Great for enthusiasts not wanting to be noticed but wanting the performance and reliability benefits of a quality 

Blow Off Valve. 

APPLICATION: 

Fits most cars using the factory BOSCH or DENSO bypass valves.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

With this Turbosmart Blow Off valve, all excess pressure is returned to the intake tract. 

Perfect for enthusiasts who do not want to attract attention, but want to take advantage of the performance and quality of a blow off valve.

Please note that for Bi-Turbo application 2 pieces are needed.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Full plumb back blow off valve. Plumb Back System returns all excess pressure back to the intake system. Ideal for fans who don\'t want to stand out, but want the performance and functional benefits of a quality BOV.

APPLICATION: Fits most vehicles with factory BOSCH or DENSO bypass valves.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The Turbosmart Shortie Compact Series valves are designed specifically for BorgWarner EFR and KKK turbos. Also suitable for the popular Ford Ecoboost engines.

Unlike standard plastic valves that use a simple rubber diaphragm, making them prone to breaking at high charge pressure. To counteract this, Turbosmart uses O-ring sealed piston on its new compact valves. This means that even boost pressures up to 30 PSI are no problem. 

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The Kompact VR02 BOV from Turbosmart was specially developed for the Hyundai Veloster Turbo. The Veloster\'s factory bypass valve is a plastic unit that becomes brittle and wears out over time. The Kompact VR02 has a unique design that fits into the tight mounting position of the Veloster\'s factory bypass valve. The result is a product that is truly a direct replacement for the OEM valve. It requires no cutting or special tools for a 100% reversible installation.

Made from billet aluminium, the VR02 cannot be overpowered by boost pressure and will not break like the standard plastic part. The plumb back configuration directs 100% of the air into the intake tract for quieter operation.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Vee-Port Pro Powersports / High Performance / Custom Builds

The legend is still alive! The VeePort Pro from Turbosmart is a further development of the original VeePort, which is now 20 % smaller and 33 % lighter. Based on the BOV5 architecture from Turbosmart, the VeePort Pro offers enormous performance in the smallest of spaces. The valve is based on the motorsport-proven Boost Balance System with a 38 mm piston and can easily deliver around 600 hp when needed and hold as much boost as you hope for.

Suitable for:

Universal and selected bolt-on applications.

Features:

• Billet aluminium construction
  
• 38mm piston made from hard anodised aluminium
  
• Handmade and tested
  
• Boost Balance technology with positive seal O-ring
  
• Aluminium V-band mounting
  
• 360 degree swivel/banjo for vacuum reference cap
• adjustable spring preload
  

Scope of delivery:

• 1 x BOV5 VeePort Pro blow off Valve
  
• 1 x Quick Release V-Band Clamp
  
• 1 x White spring with -21 to -19 InHg pre-installed
  
• 1 x 38mm weld-on adapter
  
• 360 degree swivelling vacuum connection
  
• Turbosmart Sticker
  

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Dual outlet-type BOV. Dual Port vents both to the atmosphere and back into the air intake. 

Ports with sequential timing allow quieter operation during normal driving, while getting all the benefits of a vent-

to-atmosphere BOV under race conditions. 

Easily converted to a full atmospheric or full bypass unit by using supplied port blanking plug.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Dual outlet-type BOV. Dual Port vents both to the atmosphere and back into the air intake. 

Ports with sequential timing allow quieter operation during normal driving, while getting all the benefits of a vent-

to-atmosphere BOV under race conditions. 

Easily converted to a full atmospheric or full bypass unit by using supplied port blanking plug.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Dual outlet-type BOV. Dual Port vents both to the atmosphere and back into the air intake. Ports with sequential 

timing allow quieter operation during everyday driving while getting all the benefits of a vent-to-atmosphere BOV 

under race conditions. They are easily converted to an entire atmospheric or full bypass unit using supplied port 

blanking plug.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Designed specifically for BorgWarner EFR and KKK turbos, the Turbosmart Shortie Compact Dual Port Valve is also suitable for the popular Ford Ecoboost engines. 

Using O-ring sealed piston in combination with billet aluminum construction, this valve has a boost pressure rating of 2 bar. A breakage, as with the standard plastic variants is thus avoided.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The Kompact VR02 BOV from Turbosmart was specially developed for the Hyundai Veloster Turbo. The Veloster\'s factory bypass valve is a plastic unit that becomes brittle and wears out over time. It can also break open at high boost pressure values - especially if the boost pressure is increased above the standard value.
The Kompact VR02 has a unique design that fits into the tight mounting position of the Veloster\'s factory bypass valve. The result is a product that is truly a direct replacement for the OEM valve and requires no cutting or special tools for a 100% reversible installation. Made from billet aluminium, the VR02 cannot be overpowered by boost pressure and will not break like the standard plastic part.

The Dual Port provides a stunning sound when the rider comes off the throttle while continuing to feed air back into the intake tract like the standard valve.

The Kompact VR02 Dual Port has a modular design. It can be easily converted from the standard 50:50 setting to a full recirculation or a complete bleed valve, depending on the rider\'s preference. Unscrew the unwanted fitting and replace it with the blanking plug supplied.

Suitable for Hyundai Veloster

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Turbosmart Kompact Dual Port Blow-Off Valve for all G4KF engines, such as in the Hyundai i30N and Veloster.

The award winning Kompact Series valves are the world\'s first true plug and play blow off valves. The OE BOV can be easily replaced with the Turbosmart Kompact BOV. No adapters, hoses or additional conversions are required. Turbocharger performance is enhanced by minimizing leakage, faster response, coupled with superior thermal load capacity.

• The dual port version allows a portion of the excess air into the charge air system and the other portion out into the open
• This creates a sporty soundstage.
• Patent pending integrated pressure control
• True plug-and-play upgrade
• Integrated high temperature solenoid valve
• Machined design with high temperature O-rings

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Plug & Play electronic recirculation valve for vehicles with the GM LTG 2.0 litre engine. (See vehicle list!)
Fast, high-pressure resistant valve for upgrade and motorsport turbochargers .

The valve can be replaced directly with the original valve without causing error codes on the ECU. The patented BOV is over 400% tighter than the original valve and thus enables an increase in performance.

Features:

• 100% Plug & Play
• 57 times faster than the original valve
• Over 400% tighter sealing than the original valve
• Billet design
• High temperature resistant
• Available as recirculation or dual valve

Scope of delivery:

• Turbosmart EM series recirculation (plumb back) version
• 3 X fixing screw
• Turbosmart sticker

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The award-winning Kompact EM series of retrofit bypass valves is the world\'s first true plug-and-playupgrade solution for your factory bypass valve. Unplug your OEM valve and install a Kompact EM valve in its place. No adapters, hoses or additional components are required.

The Kompact EM valve series from Turbosmart uses motorsports proven billet valve technology and adds a proprietary solenoid system and internal pressure control channels for a simple plug and play valve with full OE integration and control. There are no connecting hoses, no separate solenoids, and no complicated parts - just bolt it on and plug it in!

You can count on unmatched performance and reliability as a direct replacement for your factory bypass valve. The Kompact EM valves overcome the common failures with plastic factory valves through our boost balance valve design (The more charge you have, the better it seals), o-ring with positive seal on piston face and billet construction. Regardless of your application, the Compact EM Series will hold more charge pressure and be more responsive in every way.

Features

• Boost balance valve technology
• Patented integrated pressure control
• True plug-and-play upgrade
• Integrated proprietary high temperature solenoid valve
• Billet design with high temperature O-rings
• Can be installed in plumback or dual port versions

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Plug & Play electronic blow-off valve for vehicles with the GM LTG 2.0 litre engine. (See vehicle list!)
Fast, high-pressure resistant valve for upgrade and motorsport turbochargers .

The valve can be replaced directly with the original valve without causing error codes on the ECU. The patented BOV is over 400% tighter than the original valve and thus enables an increase in performance.

Features:

• 100% Plug & Play
• 57 times faster than the original valve
• Over 400% tighter sealing than the original valve
• Billet design
• High temperature resistant
• Available as recirculation or dual valve

Scope of delivery:

• Turbosmart EM Series BOV Dual version
• 2 X fixing screw
• Turbosmart sticker

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Weld flange (inlet) - fits Turbosmart Hyper-Gate45 (45mm) External Wastegates

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The award-winning Compact EM Series Blow-Off Valves are the world\'s first true plug-and-play blow-off valves. Unplug your OEM Blow Off valve and remove the screw and install our valve in its place. No adapters, hoses, or additional installation work is required. All of this is done while maintaining full OE control over the operation of the BOV.

Turbocharger performance is enhanced by minimizing losses, fast response and superior thermal performance thanks to our world-leading engineering and simulation capabilities.

The EM is a must-have for hybrid turbos or larger airflow turbos that use the electronic OE diverter valve, as it causes no losses and achieves target boost pressure without stressing the turbocharger and Wastegate.

Features 

• Patented integrated pressure control
• True plug-and-play upgrade
• Integrated proprietary high temperature solenoid valve
• Billet design with high temperature o-rings
• Available in plumb back or dual port options

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Turbosmart GenV Twin Port Internal Wastegate Actuator to fit Borg Warner EFR Series Turbochargers. This IWG actuator has all the technology of the award winning GenV series external wastegates and offers unparalleled actuator performance.

The Turbosmart GenV IWG (Internal Wastegate Actuator) series offers improved boost control over your factory actuator. The large working area of the unique diaphragm system provides improved response and boost control at any power or boost level.

Turbosmart\'s locking system also lets you quickly change the base spring selection from 5 to 26 psi. The Nitronic guide and hard-chrome intermediate rod, paired with the swivel joint system, ensure the best possible lower chamber seal for true twin-scroll control, unmatched actuation ranges and control.

Features 

• GenV cap with 1/8NPT ports
• True Twin Port Control for a wide boost control window
• Hard-chrome plated intermediate rod and Nitronic guide for cycle-tested and proven reliability
• Proprietary swivel linkage for full linear actuation
• 3 secondary rods included to ensure installation in all B1 & B2 single & twin scroll EFR\'s

This is an aftermarket solution for Borg Warner EFR series turbochargers, including B1 and B2 single and twin scroll turbochargers. Accessories are supplied to fit all variants, including all spring options.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The Turbosmart RacePort is famous for being an amazingly small and lightweight BOV for turbocharged competition engines. Featuring our unique collar design and internal flow structures, it is 50% lighter and 25% smaller than the competition while passing 330 CFM - making it the highest flowing BOV of its kind on the market.

Features:

• Billet 6000 series aluminium construction
• CFD controlled & optimised design
• 2.0″ / 50mm inlet flow over 330CFM
• Quick release aluminium V-band
• Unique locking collar design
• MILSPEC hard anodised valve guide and stem
• Proprietary Hi-Temp Silicon Nomex diaphragm
• Positive sealing valve seat
• Two 1/8NPT reference ports
• 5 user configurable spring options available

Scope of delivery:

• GenV RacePort 50mm BOV
• 1/8 NPT vacuum ports
• V-band assembly
• Profiled alloy for welding
• Blue spring with a pressure of -18 to -14 InHg (installed).
• Turbosmart Sticker

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Plumb Back High Performance / Custom Builds

Fully recirculating valve. A quiet alternative to the atmospheric BOV, the Plumb Back system vents all excess pressure into the intake system.

The Turbosmarts Plumb Back BOV operates quietly, just like a normal diverter valve, so you don\'t draw unnecessary and unwanted attention to yourself. The Plumb Back offers all the performance and durability benefits of a Turbosmart BOV, but with quiet operation that keeps you under the radar.

Suitable for:

Ideal for vehicles with sensitive intake systems and off-road applications, as the Plumb Back\'s fully sealed design prevents debris from entering the system.

Features:

• made from robust, durable billet aluminium
  
• Performance and reliability are paramount

Scope of delivery:

• 1 x BOV5 Plumb Back BOV
  
• 1 x Quick release V-band clamp
  
• 1 x Red spring with 17 - 14 InHg pre-installed
  
• 1 x Weld-on adapter
  

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Plumb Back High Performance / Custom Builds

Fully recirculating valve. A quiet alternative to the atmospheric BOV, the Plumb Back system vents all excess pressure into the intake system.

The Turbosmarts Plumb Back BOV operates quietly, just like a normal diverter valve, so you don\'t draw unnecessary and unwanted attention to yourself. The Plumb Back offers all the performance and durability benefits of a Turbosmart BOV, but with quiet operation that keeps you under the radar.

Suitable for:

Ideal for vehicles with sensitive intake systems and off-road applications, as the Plumb Back\'s fully sealed design prevents debris from entering the system.

Features:

• made from robust, durable billet aluminium
  
• Performance and reliability are paramount

Scope of delivery:

• 1 x BOV5 Plumb Back BOV
  
• 1 x Quick release V-band clamp
  
• 1 x Red spring with 17 - 14 InHg pre-installed
  
• 1 x Weld-on adapter
  

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Plumb Back High Performance / Custom Builds

Fully recirculating valve. A quiet alternative to the atmospheric BOV, the Plumb Back system vents all excess pressure into the intake system.

The Turbosmarts Plumb Back BOV operates quietly, just like a normal diverter valve, so you don\'t draw unnecessary and unwanted attention to yourself. The Plumb Back offers all the performance and durability benefits of a Turbosmart BOV, but with quiet operation that keeps you under the radar.

Suitable for:

Ideal for vehicles with sensitive intake systems and off-road applications, as the Plumb Back\'s fully sealed design prevents debris from entering the system.

Features:

• made from robust, durable billet aluminium
  
• Performance and reliability are paramount

Scope of delivery:

• 1 x BOV5 Plumb Back BOV
  
• 1 x Quick release V-band clamp
  
• 1 x Red spring with 17 - 14 InHg pre-installed
  
• 1 x Weld-on adapter
  

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Plumb Back High Performance / Custom Builds

Fully recirculating valve. A quiet alternative to the atmospheric BOV, the Plumb Back system vents all excess pressure into the intake system.

The Turbosmarts Plumb Back BOV operates quietly, just like a normal diverter valve, so you don\'t draw unnecessary and unwanted attention to yourself. The Plumb Back offers all the performance and durability benefits of a Turbosmart BOV, but with quiet operation that keeps you under the radar.

Suitable for:

Ideal for vehicles with sensitive intake systems and off-road applications, as the Plumb Back\'s fully sealed design prevents debris from entering the system.

Features:

• made from robust, durable billet aluminium
  
• Performance and reliability are paramount

Scope of delivery:

• 1 x BOV5 Plumb Back BOV
  
• 1 x Quick release V-band clamp
  
• 1 x Red spring with 17 - 14 InHg pre-installed
  
• 1 x Weld-on adapter
  

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Supersonic High Performance / Custom Builds

The Turbosmart BOV with the classic blow-off valve sound. The Supersonic vents completely into the atmosphere for great sound and proper performance. A full-throttle BOV for riders and serious enthusiasts looking for attention. With its unique sound, the Supersonic offers a superior flow rate. With tool-less adjustment via a twist cap and a positive sealing piston, this is the loudest BOV in the Turbosmart range.

Suitable for:

Universal fit, however some applications may require a BOV adaptor or union.

Features:

• made from robust, durable billet aluminium
  
• Performance and reliability are paramount

Scope of delivery:

• 1 x BOV5 Vent to Atmosphere (Supersonic) BOV
  
• 1 x Quick release V-band clamp
  
• 1 x Yellow spring with -22 to -20 InHg pre-installed
  
• 1 x 38mm weld-on adapter
  
• Turbosmart sticker
  

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Supersonic High Performance / Custom Builds

The Turbosmart BOV with the classic blow-off valve sound. The Supersonic vents completely into the atmosphere for great sound and proper performance. A full-throttle BOV for riders and serious enthusiasts looking for attention. With its unique sound, the Supersonic offers a superior flow rate. With tool-less adjustment via a twist cap and a positive sealing piston, this is the loudest BOV in the Turbosmart range.

Suitable for:

Universal fit, however some applications may require a BOV adaptor or union.

Features:

• made from robust, durable billet aluminium
  
• Performance and reliability are paramount

Scope of delivery:

• 1 x BOV5 Vent to Atmosphere (Supersonic) BOV
  
• 1 x Quick release V-band clamp
  
• 1 x Yellow spring with -22 to -20 InHg pre-installed
  
• 1 x 38mm weld-on adapter
  
• Turbosmart sticker
  

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Four BOVs in one. Suitable for medium-sized turbocharger systems for 4- to 6-cylinder engines with an output of 200 to 600 hp.

The Dual Port can be configured as Supersonic, Megasonic, Plumb Back or Dual Port! Features sequential ports for quiet operation at low boost pressure and full power at full boost pressure.

With a quick release V-band clamp, tool-less adjustment and all parts required for conversion, it is the most versatile BOV from Turbosmart.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Four BOVs in one. Suitable for medium-sized turbocharger systems for 4- to 6-cylinder engines with an output of 200 to 600 hp.

The Dual Port can be configured as Supersonic, Megasonic, Plumb Back or Dual Port! Features sequential ports for quiet operation at low boost pressure and full power at full boost pressure.

With a quick release V-band clamp, tool-less adjustment and all parts required for conversion, it is the most versatile BOV from Turbosmart.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The RacePort EM is a high performance valve with an output of over 2500 hp and an integrated solenoid valve for advanced control strategies and integration into OE level vehicles fitted with electronic recirculation valves.

The RacePort EM combines decades of experience with the market-leading RacePort 50mm valve with our award-winning and patented EM technology. The RacePort architecture provides market leading flow and reliability with a diaphragm actuated valve that has proven to be the most responsive and efficient valve of its kind on the market.

Features:

• Award-winning and patented EM technology
• Boost balance technology for high boost pressure
• 6000 series billet aluminium construction
• Milspec hard anodised valve guide
• High temperature silicon Nomex diaphragm
• Valve seat with positive seal
• 2\" inlet for over 330 CFM

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The Kompact Dual Port BOV kit for the Cadillac ATS-V is designed to improve turbo response and eliminate supercharger surge, improving the efficiency and longevity of the ATS-V\'s turbochargers while providing a powerful blow-off valve sound that lets everyone know what\'s under the bonnet of the Cadillac.

The Kompact Dual Port is a 50-50 atmospheric vent and recirculation valve. Its staged operation ensures that enough air is recirculated through the intake tract to satisfy the ECU and provide quiet operation at low boost pressure while maintaining the performance and sound of a breather valve.

The Dual Port\'s smart modular design also allows you to unscrew the breather flow pete and replace it with the supplied blanking plug to turn it into a complete recirculation valve for quieter, unobtrusive operation. The Dual Port from Turbosmart proves that you can have the best of both worlds!

Precision crafted from black anodised billet aluminium, the Kompact Dual Port is attractive and durable, with the strength to handle all the boost pressure you can throw at it without leaking.

Includes 2x Kompact Dual Port BOVs, Cadillac specific flange, blanking plugs and washers.

Scope of delivery:

• 2x Kompact Dual Port BOVs
• Cadillac-specific flange
• Dummy plugs

Suitable for Cadillac ATS-V 3.6TT 2015-current

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The Turbosmart Kompact BOV is a direct high-performance replacement for the stock all-plastic unit and is suitable for KIA Stinger and Genesis Sport G80 models. The Turbosmart unit is manufactured from aerospace grade billet aluminium and features high temperature gaskets that allow for minimal leakage and a complete seal across the bypass port to provide as much performance as possible.

Advantages:

• Direct upgrade for the standard BOV on KIA Stinger/Genesis Sport G80 3.3L V6 models.
• Packaged with a blanking plug to switch the unit to bleed-only or return-only mode

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Big Bubba from Turbosmart exists because sometimes bigger is simply better! Big Bubba is a piston valve for large engines with supercharging or turbocharging, including diesel engines! If you\'re looking for an inconspicuous valve for a small displacement engine, you\'ll have to look elsewhere!

The boost-balance system from Turbosmart means that the more charge you add to this valve, the better it closes and seals - it\'s as simple as that. The 2-inch piston design is an extension of our traditional BOV5 design, simply expanded to offer great flow and installation options.

Features:

• Billet aluminium construction
• 2.0 inch / 50.8 mm piston
• Manufactured, hand assembled and tested in Australia
• Boost balance technology with positive sealing O-ring
• Aluminium V-band mount
• Cap with adjustable spring preload
• Multiple spring options available (7, 12, 17 and 21 InHg)

Scope of delivery:

• Black Big Bubba with black housing
• Alloy hose adapter/welding flange
• V-band clamp
• Green spring for -12 to -8 InHg (installed)
• Turbosmart Sticker

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The Kompact BOV control unit kit contains everything you need to get your diesel or low/no vacuum engine making the right noises! This universal kit contains the Turbosmart BOV control unit and a Kompact SuperSonic 28 mm VTA (Vent to Atmosphere) blow-off valve.

The Turbosmart BOV control unit kit is a kit that contains a control unit, a solenoid valve and all the cables and hoses required for installation. The BOV control unit itself is an electrical device that receives signals from your accelerator pedal and uses them to activate a solenoid valve and bleed your chosen valve. The control unit is adjustable in terms of sensitivity and activation time so that you can customise it to your needs. The BOV controller is designed for engines such as diesel engines and other engines with \"low/no\" vacuum signal where a bleed or diverter valve is required.

The Kompact Supersonic blow-off valve is a 28mm billet aluminium BOV valve with low impact force that can withstand any boost pressure. With Turbosmarts\' Boost Balance System and a simple hose connection, the Kompact Supersonic is a VTA (Vent to Atmosphere) valve for engine compartments with space restrictions and small displacement engines!

The boost balance system from Turbosmart means that the more boost pressure you feed it, the better this valve closes and seals - it\'s as simple as that. Billet aluminium construction with a diaphragm actuated valve for the fastest possible response with V-band mounting and a range of springs to suit your requirements.

Features:

• Adjustable sensitivity
• Adjustable duration
• 6000 series billet aluminium construction
• 28 mm piston with positive seal
  
• Low Impact, Compact Finnish

Included in the scope of delivery:

• BOV control
• Compact Supersonic blow off Valve
• Wiring harness
• Solenoid valve bracket
• Silicone hose and 1/8 NPT connection kit

Installation requires wiring, welding or fabrication work is required for installation.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The PowerPort is the most significant and highest flowing blow-off valve from Turbosmart and sets new standards in flow previously set by our popular and highly regarded RacePort BOV. It has been designed to be as light as possible to minimise vehicle weight. The state-of-the-art dual-chamber design allows for advanced control strategies. It can be held open with a solenoid valve to aid turbo response and control during the launch phase, allowing for the best possible launch in drag racing etc..

With over 600 CFM of flow through its 2.5-inch (63 mm) intake, this diaphragm-actuated valve is designed to flow large volumes of air for high horsepower applications while providing market-leading responsiveness and boost handling. Twin port control enables advanced control strategies. Options include an integrated valve position sensor and specific part numbers for supercharged applications. However, it can also be used with a conventional single port.

Features:

• Billet aerospace aluminium housing
• Quick release V-band
• 2.5 \" intake for a flow rate of over 600 CFM
• MILSPEC hard anodised valve
• Positive valve seat
• Twin 1/8\" NPT port on lower chamber for advanced control strategies
• -4 AN top port
• Special cap for quick spring replacement
• Activation range from 4inHg to 20inHg
• Optional valve position sensor
• 3 configurable corrosion resistant springs
• Pre-drilled collar for safety wire attachment

Scope of delivery:

• Power Port BOV
• 1/4\" -4AN nipple
• 1/8\" NPT blanking plug
• 1/8\" NPT nipple
• Profiled intake weld-on flange (alloy)
• Collar tool
• Turbosmart-Sticker
  

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The BOV 5 BOV control unit kit contains everything you need to get your diesel or low/no vacuum engine making the right noises! This universal kit contains the Turbosmart BOV control unit and a BOV5 SuperSonic 38 mm VTA (Vent to Atmosphere) blow-off valve. The Turbosmart BOV control unit kit is a kit that contains a control unit, a solenoid valve and all the cables and hoses required for installation.

The BOV control unit itself is an electrical device that receives signals from your accelerator pedal and uses them to activate a solenoid valve and bleed the valve you have selected. The control unit is adjustable in terms of sensitivity and activation time so that you can customise it to your needs. The BOV controller is designed for engines such as diesel engines and other engines with \"low/no\" vacuum signal where a bleed or diverter valve is required.

The Turbosmart BOV5 is a 5th generation piston style blow-off valve based on a 38mm piston with positive sealing for excellent flow and tightness. The BOV5 SuperSonic is a totally reliable piston actuated valve based on our Boost Balance System and features V-band mounting, aluminium construction and zero preload adjustment.

The boost balance system from Turbosmart means that the more boost pressure you feed it, the better this valve closes and seals - it\'s that simple. Billet aluminium construction with a diaphragm actuated valve for the fastest possible response with V-band attachment and a range of springs to suit your requirements.

Features:

• Adjustable sensitivity
• Adjustable duration
• 6000 series billet aluminium construction
• 38 mm / 1.5″ piston with positive seal
• Rotatable banjo reference screw connection
• Tool-free adjustment of the preload
• Large selection of fittings and accessories

Included in the scope of delivery:

• BOV control unit
• BOV5 Supersonic blow off Valve
• Aluminium welding flange
• Wiring harness
• Solenoid valve and bracket
• Silicone hose and 1/8 NPT fitting kit

Wiring, welding or fabrication work is required for installation.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The Big Bubba BOV ECU kit contains everything you need to get your low/no vacuum diesel or engine making the right noises! This universal kit contains the Turbosmart BOV control unit and a Big Bubba VTA (Vent to Atmosphere) blow-off valve. The Turbosmart BOV control unit kit is a kit that contains a control unit, a solenoid valve and all the cables and hoses required for installation.

The BOV control unit itself is an electrical device that receives signals from your accelerator pedal and uses them to activate a solenoid valve and bleed the valve you have selected. The control unit is adjustable in terms of sensitivity and activation time so that you can customise it to your needs. The BOV controller is designed for engines such as diesel engines and other engines with \"low/no\" vacuum signal where a bleed or diverter valve is required.

Big Bubba from Turbosmart exists because sometimes bigger is simply better! Big Bubba is a piston valve for large engines with supercharging or turbocharging, including diesel engines! If you\'re looking for an inconspicuous valve for a small displacement engine, you\'ll have to look elsewhere!

The boost balance system from Turbosmart means that the more boost pressure you feed it, the better this valve closes and seals - it\'s that simple. Billet aluminium construction with a diaphragm actuated valve for the fastest possible response with V-band mounting and a range of springs to suit your requirements.

Features:

• Adjustable sensitivity
• Adjustable duration
• 6000 series billet aluminium construction
• 2.0 inch / 50.8 mm piston
• Manufactured, hand assembled and tested in Australia
• Boost balance technology with positive sealing O-ring Aluminium
• V-band mount

Included in the scope of delivery:

• BOV control unit
• 
  
• Aluminium welding flange
• Wiring harness
• Solenoid valve and bracket
• Silicone hose and 1/8 NPT fitting kit

Wiring, welding or fabrication work is required for installation.

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The RacePort BOV control unit kit contains everything you need to get your diesel or low/no-vacuum engine making the right noises! This universal kit contains the Turbosmart BOV control unit and a RacePort 50 mm VTA (Vent to Atmosphere) blow-off valve.

The Turbosmart BOV controller kit contains a controller, a solenoid valve and all cables and hoses required for installation. The BOV controller is an electrical device that receives signals from your accelerator pedal and uses them to activate a solenoid valve and vent the valve you have selected. The sensitivity and activation time are adjustable so you can customise it to your needs. The BOV controller is designed for engines such as diesel engines and other low/no vacuum signal engines where a bleed or diverter valve is required.

The Turbosmart RacePort is known as an amazingly small and lightweight BOV for high performance competition engines. With our unique collar design and internal flow structures, it is 50% lighter and 25% smaller than the competition and has a flow of 330 CFM - making it the highest flowing BOV of its kind on the market.

The boost balance system from Turbosmart means that the more boost pressure you feed it, the better this valve closes and seals - it\'s that simple. Billet aluminium construction with a diaphragm actuated valve ensures the fastest possible response with V-band attachment and a range of springs to suit your needs.

Features:

• Adjustable sensitivity
• Adjustable duration
• 6000 series billet aluminium construction
• CFD assisted and optimised design
• 2.0″ / 50 mm inlet flow over 330 CFM
• Quick release V-band
• Unique design of the locking collar
• MILSPEC hard anodised valve guide and valve stem
• High temperature resistant proprietary silicone Nomex diaphragm
• Positive sealing valve seat
• Two 1/8 NPT reference ports
• 5 user configurable spring options available

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

The Power port with sensor cap for data acquisition/logging is also Turbosmart\'s largest blow-off valve with the highest flow rate. Designed to be as light as possible and keep vehicle weight low. The innovative dual-chamber design allows it to be held open using an electromagnet to aid turbocharger response and control during staging to ensure the best possible start and the integrated position sensor allows you to see what the BOV is doing. The sensor provides an easily analysable analogue signal (0-5V) for connection to the data logger. The data collected in this way can be used to maximise turbocharger performance.

With a flow rate of over 600 CFM through its 2.5-inch (63 mm) intake, this diaphragm-actuated valve is designed to flow large volumes of air for high performance applications while providing market-leading responsiveness and boost handling. Twin port control enables advanced control strategies. Options include an integrated valve position sensor and specific part numbers for supercharged applications. However, it can also be used with a conventional single port.

Features:

• 6000 series billet aluminium construction
• Quick release V-band collar for easy installation and maintenance
• 2.5-inch intake and flow over 600 CFM
• MILSPEC hard anodised valve
• 1/8NPT reference ports (dual port)
• Collar-secured cap for quick spring replacement and maintenance
• 3 user configurable corrosion resistant springs
• Optional valve position sensor
• Pre-drilled collar for safety wire Designed, manufactured and validated in Australia

Scope of delivery:

• PowerPort Black with sensor cap
• 1/4″-4AN nipple
• 1/8″ NPT blanking plug
• 1/8″ NPT nipple
• Profiled intake welding flange (alloy) and collar tool.
• Turbosmart-Sticker

Manufacturer

Information about the manufacturer

Turbosmart

Turbosmart UK Ltd

Unit 4, Wharton Street Industrial Estate, Nechells, Birmingham, B75TR, United Kingdom

[email protected]

EU responsible person

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]