Разпределителни валове VW

 

Camshaft for all Polo G40Modells asymetric.

More torque and HP for your engine.

PLUS

New set of SCHRICK Lifters.

Manufacturer

Information about the manufacturer

BAR-TEK®

BAR-TEK Motorsport GmbH

Im Rauschen Auel 3, 51491 Overath-Brombach, Germany

[email protected]

Original Alu Schrick valve cover for VW Golf 1 and Golf 2 8V engines is back.

Design of the 80s and today´s quality.

Features:

• High quality cast aluminum
• cooling ribs
• 80s design

This Schrick valve cover is perfect for your VW golf engine.

Fits for:

• 1.6-2.0L 8V 827 engines
• 1.8L G60 engines

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

 

High capacity Schrick oil pan for all 4 bore VW Engine.
Increase oil cooling capabilities. 0,75l bigger oilvolume.
Helps keeping oil at the pump pick-up tube.
The ability to keep the oil at the pick-up tube will make sure that no dangerous air will be sucked from the oilpump while taking hard turns for example.

With drain plug and bolts included.

Also for 16V Engines!
No gasket included.

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

\"Asymetric Camshaft for VW Polo 1.0-1.6L

264°/260°, cam lift 9,8, valve lift at TDC 0,9, for hydr. lifters

Check valve springs, avoid coil bind!

Putting a Sports-Cam in your engine new Lifters must be used to prevent premature cam lobe wear, otherwise the product warranty will be void!
\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

 

Camshaft for VW Polo 1.0-1.6L

268°/264°, cam lift 10/9,8, valve lift at TDC 1,2, for hydr. lifters

Ceck valve aprings, avoid coil bind!

Putting a Sports-Cam in your engine new Lifters must be used to prevent premature cam lobe wear, otherwise the product warranty will be void!

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Best camshaft for all G-40 models. 252°/276° asymmetrical!

Special camshaft for all G40.

More torque and power! Suitable up to 170 HP

252°, cam lift 9,6/10,0, valve lift in TDC 0,7/1,3, for Hydros

It is absolutely to be paid attention to the fact that Schrick grants only warranty, if with the installation also new hydro tappets are used!

(subject to registration)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Camshaft for VW Polo 1.0-1.6L 

268°/264°, cam lift 10/9,8, valve lift at TDC 1,2, for hydr. lifters 

Ceck valve aprings, avoid coil bind! 

Putting a Sports-Cam in your engine new Lifters must be used to prevent premature cam lobe wear, otherwise the product warranty will be void!

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Camshaft for all G-60 models. 272° symetric!

More torque and power!
Extreme camshaft for G-60 tuning.

272°, cam lift 11,4, valve lift in TDC 1,6/1,7, for Hydros

It is absolutely to be paid attention to the fact that Schrick grants only warranty, if with the installation also new hydro tappets are used!

(subject to registration)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Camshaft for all G-Modells 268° symetric.
More torque and HP for your engine.

268°, cam lift 11,2, valve lift at TDC 1,2, for hydr. lifters

Putting a Sports-Cam in your engine new Lifters must be used to prevent premature cam lobe wear, otherwise the product warranty will be void!

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Camshaft from Schrick 276° symmetrical!

More torque and power!

276°, cam lift 11,5, valve lift in TDC 2,1, for Hydros

It is absolutely to be paid attention to the fact that Schrick grants warranty only if with the installation also new hydro tappets are used!

(subject to registration)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Camshaft from Schrick for all G-60 models. 288° symetric!

More torque and power!

Extreme camshaft for G-60 tuning.

288°, cam lift 11,7, valve lift in TDC 2,9, for Hydros

It is absolutely to be paid attention to the fact that Schrick grants only warranty, if with the installation also new hydro tappets are used!

(subject to registration)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Camshaft for all 827 Blocks (1,5L to 2,0L) like in the Golf, Scirocco, Jetta, Passat, Vento or Polo Classic from year 2000 onwards.

More torque and HP for your engine.

260°, cam lift 11,0, valve lift at TDC 0,6/0,7, for hydr. lifters

Putting a Sports-Cam in your engine new Lifters must be used to prevent premature cam lobe wear, otherwise the product warranty will be void!

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

 

Camshaft for all G-Modells. 268°/276° asymetric.

More torque and HP for your engine.

268°/276°, cam lift 11,2/11,5, valve lift at TDC 1,3/1,8, for hydr. lifters

Putting a Sports-Cam in your engine new Lifters must be used to prevent premature cam lobe wear, otherwise the product warranty will be void!

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Camshaft Schrick for VW Golf 1 GTI 1.6-1.8L

More torque and Horsepower!

276°, cam lift 11,3, valve lift at TDC 2,7, valve clearance 0,35/0,45

Please secure, that the cams are free travelling!

(Pic shows different cams)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Camshaft Schrick for VW Golf 1 GTI 1.6-1.8L

More torque and Horsepower!

288°, cam lift 11,7, valve lift at TDC 3,4, valve clearance 0,35/0,45

Please secure, that the cams are free travelling!

(Pic shows different cams)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

\"2 x Camshafts Schrick for VW 16V small block 4 Cyl. 4 valve roller cam follower (Polo, Lupo, Golf 4, Arosa, Felicia)

More torque and Horsepower!

Intake: 244°, cam lift 4,69 (9,0), valve lift at TDC 0,7, for hydr. lifters
Exhaust: 244°, cam lift 4,69 (9,0), valve lift at TDC 0,7, for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)
\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

\"2 x Camshafts Schrick for VW 16V small block 4 Cyl. 4 valve roller cam follower (Polo, Lupo, Golf 4, Arosa, Felicia)

More torque and Horsepower!

Intake: 252°, cam lift 4,69 (9,0), valve lift at TDC 0,75, for hydr. lifters
Exhaust: 252°, cam lift 4,69 (9,0), valve lift at TDC 0,75, for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)
\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

\"2 x Camshafts Schrick for VW 16V small block 4 Cyl. 4 valve roller cam follower

For engines with variable intake camshaft!

More torque and Horsepower!

Intake: 256°, cam lift 4,80 (9,15), valve lift at TDC 0,1, for hydr. lifters
Exhaust: 252°, cam lift 4,69 (9,0), valve lift at TDC 0,75, for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)
\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

\"2 x Camshafts Schrick for VW 16V small block 4 Cyl. 4 valve roller cam follower

For engines with variable intake camshaft!

More torque and Horsepower!

Intake: 256°, cam lift 4,80 (9,15), valve lift at TDC 0,1, for hydr. lifters
Exhaust: 244°, cam lift 4,69 (9,0), valve lift at TDC 0,7, for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)
\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

VR6 sports camshaft set SCHRICK 264°

2 Sport camshafts from Schrick for all VR6 2 Vent. engines.

More torque and power!

264°, cam lift 11.4/11.2, valve lift in TDC 0.91/0.75, for hydros

Attention: Schrick only grants warranty on the camshafts if new hydro tappets are also installed.



Must be registered!

(Image similar)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

 \"2 Camshafts original Schrick for VR6 2 valve engines.

More torque and horsepower!

276°, cam lift 11,5, valve lift at TDC 2,08/2,20, for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)

\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

2 Sport camshafts from Schrick for all 16 V Polo engines.

More torque and power!

Intake 256°, cam lift 9,5, valve lift in TDC 0,6, for Hydros
exhaust : 256°, cam lift 9,5, valve lift in TDC 0,7, for Hydros

It is absolutely to be paid attention to the fact that Schrick grants only warranty, if with the installation also new hydro tappets are used!



(subject to registration)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

2 Sport camshafts from Schrick for all 16 V Polo engines.

More torque and power!

Intake: 264°, cam lift 10,0, valve lift in TDC 1,1, for Hydros
exhaust : 264° cam lift 10,0, valve lift in TDC 1,2, for Hydros

It is imperative to note that Schrick only grants warranty if new hydro tappets are also used during installation!

Please specify whether cups or hydro tappet head!

(subject to registration)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

 

\"2 x Camshafts Schrick for VW 16V small block 4 Cyl. 4 valve roller cam follower (Polo, Lupo, Golf 4, Arosa, Felicia)

More torque and Horsepower!

Intake: 268°, cam lift 4,80 (9,15), valve lift at TDC 0,8, for hydr. lifters
Exhaust: 268°, cam lift 4,80 (9,15), valve lift at TDC 0,8, for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)
\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

2 Sport camshafts from Schrick for all VR6 2 Vent. Engines.

More torque and power!

268°, cam lift 11.4, valve lift in TDC 0.8/1.1, for hydros

Attention: Schrick only grants warranty on the camshafts if new hydro tappets are also installed.

Registration required!

(Picture similar)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

 

\"2 Camshafts original Schrick for 16 Valve engines 1.8 - 2.0L

More torque and horsepower!

Intake 260°, cam lift 11,2, valve lift at TDC 0,9, for hydr. lifters
Exhaust 260°, cam lift 11,2, valve lift at TDC 1,0, for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)


\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

2 Sport camshafts from Schrick for all 16 V Polo engines.

More torque and power!

Note: Schrick valve springs, valve spring retainers and balancing parts must be installed. You can find them below under accessories.

intake: 292°, cam lift 11,6, valve lift in TDC 4,2, valve clearance 0,25
exhaust : 292° cam lift 11,6, valve lift in TDC 4,2, valve clearance 0,30

Base circle radius R=15,5 (1,5mm smaller than stock)

Registration required, picture similar

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

 

\"2 x 268° Camshafts original Schrick for 16 Valve Engines.

More torque and Horsepower!

Intake 268°, cam lift 11,5, valve lift at TDC 1,6, for hydr. lifters
Exhaust 268°, cam lift 11,5, valve lift at TDC 1,7, for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)
\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

2 Sport camshafts from Schrick for all 16 V engines.

More torque and power!

Note: New Schrick tappets must be installed! You can find them below under accessories.

intake: 284°, cam lift 11,6, valve lift in TDC 3,1, valve clearance 0,25
exhaust : 284°, cam lift 11,6, valve lift in TDC 3,1, valve clearance 0,30

New SCHRICK tappets must be installed!

Attention: Schrick only grants warranty on the camshafts if new tappets are installed.

Registration required!

(Picture similar)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

\"2 Camshafts Schrick for 16V engines 1.8 - 2.0L

More torque and horsepower!

Intake: 276°, cam lift 11,5, valve lift at TDC 2,4, for hydr. lifters
Exhaust: 276°, cam lift 11,5, valve lift at TDC 2,5, for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)
\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

\"276° and 268° Camshafts original Schrick for 16G60 Engines.

More torque and Horsepower!

Only fpr 16VG60 Conversion.

Intake 276°, cam lift 12,5mm valve lift at TDC 1,9mm for hydr. lifters
Exhaust 268°, cam lift 11,5mm valve lift at TDC 1,7mm for hydr. lifters

Attention: Schrick will only give warranty if for assembly NEW hydraulic lifters will be used!

(Pic shows different cams)
\"

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

2 Sport camshafts from Schrick for all 16 V engines.

More torque and power!

Note: New Schrick valve springs, valve spring retainers, valve wedges and tappets must be installed! You can find them below under accessories.

intakevalve springs: 300°, cam lift 12,0, valve lift in TDC 4,2, valve clearance 0,25
exhaust : 300°, cam lift 12,0, valve lift in TDC 4,2, valve clearance 0,30

Attention: Schrick only grants warranty on the camshafts if new tappets are installed!

Registration required!

(Picture similar)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

Complete conversion Kit for VW Golf G60

SCHRICK camshaft 272°
16 valve springs
8 valve spring retainers titanium
8 valve spring retainers steel
16 keys
8 hydr. lifters

Please secure, that the cams are free travelling!

(Pic shows different kit)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

 

Complete conversion Kit for VW Golf G60

SCHRICK camshaft 268°/276°
16 valve springs
8 valve spring retainers titanium
8 valve spring retainers steel
16 keys
8 hydr. lifters

(Pic shows different kit)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]

2 Sport camshafts from Schrick for all 16 V Polo engines.

More torque and power!

Note: Schrick valve springs, valve spring retainers and balancing parts must be installed. You can find them below under accessories.

intake: 280°, cam lift 10,4, valve lift in TDC 3,0, valve clearance 0,25
exhaust : 280° cam lift 10,4, valve lift in TDC 3,0, valve clearance 0,30

Base circle radius R=16,5 (0,5mm smaller than stock)

(registration required)

(picture similar)

Manufacturer

Information about the manufacturer

SCHRICK

AVL SCHRICK Performance Components GmbH

Dreherstraße 5, 42899 Remscheid, Germany

[email protected]